The upper hose inlet tube had to be moved outward to fit any fan shroud. I run the short Jaguar fan clutch (Hayden #2765) because of the thick radiator and 70-up taller aluminum water pump. The car still performed pretty darn good with a skimpy looking fan and no shroud. So I cut off each blade of a 5 blade and made a fan. When we first built the motor, the Champion upper radiator hose mounted way too close to the center and hit my 5 blade MP fan kit. The fan by itself just could not pull enough air without the car moving. Once in 88 degree heat I got stuck in road construction barely moving for 20 minutes. No major cooling problems, but I don't run a fan shroud. I run distilled water and Justice Brothers Radiator Cooler (RC/22P) and Justice Brothers Cooling System Protector ( CSP/1P). Radiator looks great inside, no rust, and no measured electrolysis. I've put 3458 miles on the motor in 1 ½ years and driven a few times 80 miles to/from Willow Springs Raceway racing 60 laps/150 miles going about 1 rpm on straights. $10 for the 2 sheets of ABS plastic, $40 for 2 Silent Wings 3 120mm PWM High Speed fans, and $10 for the Argus Monitor software. If you have any questions or want a more detailed how to guide just let me know.I have a Champion 4 core 228221 radiator that has performed well in my new 416 stroker small block. When creating the fan curve, I did have to increase the rpm to completely drown it out but 1600 rpm at 17 dB(A) is perfectly fine and it was better than my goal of 20 dB(A). While it does make some noise, the fans are able to drown it out even at low rpm. When I first started this project, I was concerned about coil whine/ electrical noise but this ended up not being a problem. Keep in mind that all testing was done with the side panel on and with the fan curves shown below. Additionally, the case fans are 3x pure wings 2 140mm fans at low speed , a 1tb ssd since hard drives are not quiet, and a 850 watt power supply because it can maintain 360 watts without the fan running.Īrgus Monitor: Idle Stressing both CPU and GPU The CPU cooler I use is a Be Quiet Dark Rock Pro 3 and is able to passively cool my i5-8600k OC to 4.8GHz while idle and when stress tested the temps reach 82 ☌ with the fans peaking at 60% (about 1000 rpm). The GPU is running at the factory OC: 1753MHz for GPU and 4050MHz for memory. While idle, my computer is under 12 dB(A) (again according to Be Quiet) since the fans only need to spin at 12% (about 260 rpm). I am unable to test this as the ambient dB(A) in the room is around 24-26 but I can confirm that I am unable to hear it (my computer is on a table 2 feet away). I did cut two notches in the back panel in order to slide the fans in and out (shown in the first picture).Īfter stress testing, the GPU peaked at 76 ☌ and the max rpm of the fans is 65% (just under 1600 rpm) and according to Be Quiet is about 17 dB(A). I also cut out the piece for the fans so connect to.Īfter that I was just cutting the four side pieces and gluing them together. I then measured the distance between the screw holes, made a template, and cut it out. Removing the stock shroud was easy, just four screws and unplugging the fan and rgb cables. I got the plastic from Amazon and went with 12" by 12" by 1/8" ABS sheets ( link). For software, I used Argus Monitor for fan speed control. Once replaced with Be Quiet Silent Wings 3 120mm PWM High Speed fans the minimum is now 12% (about 260 rpm).įor this mod I used some sheets of ABS plastic, a jig saw to cut it, and superglue. Since the mod was fairly simple, I figured others would be interested in it as it won't void any warranty or require a full teardown. I did this mod on my Zotac 1070ti AMP because the default fans have a minimum speed of 40% (about 1300 rpm). I created a custom shroud for my graphics card so I could replace the stock 80mm fans with 120mm fans.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |